Chemin:okDatasheet > Fiche de Semi-conducteurs > MaximIC Datasheet > MaximIC-162

AX485CPA MAX6320PUK27CX-T MAX502BENG MAX4519MJD MAX4598CWP MAX6316LUK41AX-T MAX4220ESD MAX906C/D MX7547UQ MAX4174AHEUK-T MAX2267E/D MAX230CWP MAX829C/D MAX6316LUK33CW-T MAX6310UK31D4-T MAX6346XR45-T MAX8212ETY MAX6322HPUK45D-T MX7543SQ MAX803ZEXR-T10 MAX6310UK48D2-T MAX6711LEXS-T

MaximIC Fiches catalogue-162

Partie nFabricantApplication
DG425CY MaximICImproved low-pover, CMOS analog switches with latches
MAX873BMJA MaximICLow-power, low-drift precision voltage reference. 2.5V+-2.5mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC.
MAX485CPA MaximICLow-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32.
MAX6320PUK27CX-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms
MAX502BENG MaximICVoltage-output, 12-bit multiplying DAC. Error(LSBs) +-3/4.
MAX4519MJD MaximICPrecision, dual 2-channel, low-voltage, CMOS analog multiplexer. Single-supply operation (+2.2V to +15V) or bipolar-supply operation (+-2.2V to +-8V).
MAX4598CWP MaximICLow-voltage, CMOS analog IC, combination single-ended 8-to-1/differential 4-to-1 multiplexer.
MAX6316LUK41AX-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.100V, min reset timeout 1ms, typ watchdog timeout 102ms
MAX4220ESD MaximICQuad, miniature, 200MHz -3dB bandwidth, single 3.3V/5.0V operation, Rail-to-Rail op amp with enable.
MAX906C/D MaximICDual, high-speed, positive edge-triggered, ECL-compatioble voltage comparator.
MX7547UQ MaximICCMOS parallel loading dual 12 bit multiplying D/A converter. Gain error +-2 LSB.
MAX4174AHEUK-T MaximICSingle, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 2.5, 1+ (Rf/Dg) noninverting gain 3.5, -3dB BW 820kHz.
MAX2267E/D MaximIC2.7V, single-supply, cellular-band linear power amplifier. Low average CDMA current consumption in typical urban scenario 55mA. TSSOP-EP 5mm x 6.4mm.
MAX230CWP MaximIC+5V-powered, multichannel RS-232 driver-receiver.
MAX829C/D MaximICSwitched-capacitor voltage inverter. 35kHz. +1.5V to +5.5V input voltage range.
MAX6316LUK33CW-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low push/pull). Factory-trimmed reset threshold(typ) 3.300 ,min reset timeout 140ms,typ watchdog timeout 6.3ms
MAX6310UK31D4-T MaximICMultiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.003(min),3.157(max). Nominal timeout period 1120ms.
MAX6346XR45-T MaximICMicroprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 4.500V. Order increment 10k
MAX8212ETY MaximICMicroprocessor voltage monitor with programmable voltage detection. High output current capability.
MAX6322HPUK45D-T MaximICMicroprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 1120ms
MX7543SQ MaximICCMOS serial input 12 bit DAC. Error +1 LSB.
MAX803ZEXR-T10 MaximICMicroprocessor reset circuit Reset threshold 2.32V. Open-drain active-low reset. 10k increments.
MAX6310UK48D2-T MaximICMultiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 4.680(min),4.920(max). Nominal timeout period 20ms.
MAX6711LEXS-T10 MaximICMicroprocessor reset circuit with manual reset input. Reset threshold 4.63V. Output type active-low push-pull reset.
MAX6318MHUK25DW-T MaximICMicroprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 1.12sec, watchdog timeout(typ) 6.3ms
MAX4174AKEUK-T MaximICSingle, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 4, 1+ (Rf/Dg) noninverting gain 5, -3dB BW 970kHz.
MAX414BEPD MaximICQuad, 28MHz, low-noise, low-voltage, precision op amp.
MAX704CSA MaximICLow-cost microprocessor supervisory circuit with battery backup. Precison supply-voltage monitor 4.40V.
MAX876BEPA MaximICLow-power, low-drift precision voltage reference. 10V+-5.0mV output (Ta=25gradC). TEMPCO(max) 20ppm/gradC.
MAX6318MHUK44CX-T MaximICMicroprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms

<< 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 >>