Chemin:okDatasheet > Fiche de Semi-conducteurs > MaximIC Datasheet > MaximIC-248

MAX379EWG MAX487EPA MAX972CPA MAX1246ACEE MAX1617MEE MAX6318MHUK29CZ-T ICL7642CMJD MXL1001ACS8 MAX6326XR30-T MAX6317HUK34CX-T MAX6313UK35D3-T MAX6321HPUK46CW-T MAX6319LHUK26D-T MX7545ATQ MAX477EUA MAX199BCAI MAX8866SEUA MAX803TEXR-T MAX1542ETP MAX6318LHUK37BZ-T MAX184BC/D MAX466

MaximIC Fiches catalogue-248

Partie nFabricantApplication
MAX207CAG MaximIC+5V RS-232 transceiver with 0.1 microF external capacitors
MAX4582CEE MaximICLow-voltage, CMOS analog multiplexer (two 4-channel).
MAX379EWG MaximICHigh-voltage, fault-protected analog multiplexer.
MAX487EPA MaximICLow-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 128.
MAX972CPA MaximICUltra-low-power, open-drain, dual comparator. Internal precision reference none. Internal hysteresis no.
MAX1246ACEE MaximIC+2.7V, low-power, 4-channel, serial 12-bit ADC. INL (LSB) +1/2,-1/2
MAX1617MEE MaximICRemote/local temperature sensor with SMBus serial interface
MAX6318MHUK29CZ-T MaximICMicroprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec
ICL7642CMJD MaximICQuad operational amplifier, 10mV
MXL1001ACS8 MaximICPrecision operational amplifier
MAX6326XR30-T MaximICUltra-low-power microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 3.000V. Order increment 10k
MAX6317HUK34CX-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.400V, min reset timeout 140ms, typ watchdog timeout 102ms
MAX6313UK35D3-T MaximICMultiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 3.413(min) 3.588(max).Nominal timeout period 140ms.
MAX6321HPUK46CW-T MaximICMicroprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.630V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms
MAX6319LHUK26D-T MaximICMicroprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 1120ms
MX7545ATQ MaximICTTL/CMOS compatible for Vdd = 5V or CMOS compatible for Vdd = 15V, 12-bit buffered multiplying DAC. Gain error +-3 LSB.
MAX477EUA MaximIC300MHz high-speed op amp.
MAX199BCAI MaximICMulti-range (+-4V, +-2V, +4V, +2V), +5V supply, 12-bit DAS with 8+4 bus interface
MAX8866SEUA MaximICDual, low-dropout, 100mA linear regulator with auto-discharge function. Preset output voltage 2.84V
MAX803TEXR-T MaximICMicroprocessor reset circuit Reset threshold 3.08V. Open-drain active-low reset. 2.5k increments.
MAX1542ETP MaximICTFT LCD DC-to-DC converter with operational amplifiers
MAX6318LHUK37BZ-T MaximICMicroprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.700V min, reset timeout 20ms,typ watchdog timeout 25.6sec
MAX184BC/D MaximICHigh-speed 12-bit A/D converter with external reference input. 5 microsec. max conversion time. Linearity(LSB) +-1.
MAX466CNI MaximICTwo-channel, quad RGB switch and buffer. Voltage gain 2V/V.
MAX520ACPE MaximICQuad, 2-wire serial 8-bit DAC with Rail-to-Rail, unbuffered outputs. TUE(LSB) 1.
MAX6318MHUK49AY-T MaximICMicroprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec
MAX789CCK MaximIC3V 5A step-down, PWM, switch-mode DC-DC regulator.
MAX6318MHUK42CX-T MaximICMicroprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.200V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms
MAX786C/D MaximICDual-output power-supply controller for notebook computers
MAX814NCSA MaximIC+-1% accuracy, low-power, microprocessor supervisory circuit. Reset trip threshold (min) 4.50V (max) 4.60V, push-pull active-low reset output, push-pull active-high reset output, manual reset, power-fail monitor, low-line detector.

<< 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 >>