| Partie n | Fabricant | Application |
|---|
| MAX329EWE | MaximIC | Ultra-low lealage monolithic CMOS analog multiplexer. |
| MAX4074BGEUK-T | MaximIC | Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 30V/V, noniverting gain 31V/V, -3dB BW 89kHZ. |
| MAX6353LTUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.63V (Vcc5) and 3.08V (Vcc3). Active-low push-pull reset 5V. |
| MAX6321HPUK25CX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX8211EPA | MaximIC | Microprocessor voltage monitor with programmable voltage detection. Define output current limit. |
| MAX6328XR25-T | MaximIC | Ultra-low-power microprocessor supervisory circuit (reset output active-low, open-drain). Reset threshold (typ) 2.500V. Order increment 10k |
| MXL1007MH | MaximIC | Low-noise, precision operational amplifier. |
| MAX6320PUK49DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| MX7820KCWP | MaximIC | CMOS highspeed 8-bit A/D converter with reference and track/hold function. Error +,-1 LSB |
| MAX6317HUK42BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.200V, min reset timeout 20ms, typ watchdog timeout 102ms |
| MAX4012EUK | MaximIC | Low-cost, high-speed, SOT23, single-supply op amp with Rail-to-Rail outputs. High speed 200MHz - 3dB bandwidth. Transistor count 95 . |
| DG201ACK | MaximIC | Quad SPST CMOS analog switch. |
| MAX6318LHUK45CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.500V min, reset timeout 140ms,typ watchdog timeout 6.3ms |
| MAX1666VEEP | MaximIC | Advanced lithium-lon battery-pack protector |
| MAX8885EUK33 | MaximIC | 150mA, low-dropout, linear regulator with power-OK output. Preset output voltage 3.3V. |
| MAX5133AEEE | MaximIC | +3V, 13-bit, serial, force/sense DAC. Built-in 10ppm/C(max) precision bandgap reference +1.25V. INL (LSB) +-1. |
| MAX6322HPUK40B-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.000V, reset timeout(min) 20ms |
| MAX6332UR25D2-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit Reset threshold(typ) 2.5V, reset timeout(min) 20ms |
| ICL7621DCTV | MaximIC | Dual operational amplifier, 15mV |
| MAX4217EUA | MaximIC | Dual, 230MHz -3dB bandwidth, single 3.3V/5.0V operation, gain of +2V/V or -1V/V, closed-loop, Rail-to-Rail buffer. |
| MAX474CSA | MaximIC | Dual, 10MHz single-supply op amp. |
| MAX264BEPI | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 2%. |
| MXD1000PA50 | MaximIC | 5-tap silicon delay line |
| MAX903CSA | MaximIC | High-speed, low-power voltage comparator |
| MAX6316LUK47CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.700V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX3748ETE | MaximIC | Compact 155Mbps to 3.2Gbps limiting amplifier |
| MXD1005SE250 | MaximIC | 5-tap silicon delay line |
| MAX878ESA | MaximIC | Step-up/step-down DC-DC converters |
| MAX8215MPD | MaximIC | +-5V, +-12V dedicated microprocessor voltage monitor. |
| MAX542BESD | MaximIC | +5V,serial-input, voltage-output, 16-bit DAC. INL (LSB) +-2 |
