| Partie n | Fabricant | Application |
|---|
| MAX394EWP | MaximIC | Precision, quad, SPST analog switch |
| DG401C/D | MaximIC | Improved, dual, SPST, NO high-speed analog switch |
| MAX367EPN | MaximIC | Signal-line circuit protector. |
| MAX1113MJE | MaximIC | 5 V, low-power, multi-channel, serial 8-bit ADC. 4-channel single-ended or 2-channel differential inputs |
| MAX4052EEE | MaximIC | Low-voltage, CMOS analog multiplexer |
| MAX674MJA | MaximIC | +10V precision voltage reference. Temp. coefficient ppm/degC 20. Initial error 15mV |
| MAX1490BCPG | MaximIC | Complete, isolated RS-485/RS-422 data inteface. |
| MAX868EUB | MaximIC | Regulated, adjustable -2x inverting charge pump |
| MAX4305EUK-T | MaximIC | Low-noise, low-distortion op amp. Bandwidth 340MHz. Minimum stable gain 10V/V. |
| MAX6316MUK43BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.300V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX4603CAE | MaximIC | Low on-resistance (2.5om max), quad, SPST, CMOS analog switches (two NO and two NC switches). |
| MAX4523CSE | MaximIC | Quad, low-voltage, SPST analog switch. |
| MXD1210EPA | MaximIC | Nonvolatile RAM controller |
| MAX6307UK32D1-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds3.120(min),3.280(max).Nominal timeout period 1ms. |
| MAX6313UK49D4-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 4.778(min) 5.023(max).Nominal timeout period 1120ms. |
| MAX6307UK26D3-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds2.564(min),2.696(max).Nominal timeout period 140ms. |
| DG423AK | MaximIC | Improved low-pover, CMOS analog switches with latches |
| MAX6318LHUK36AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.600V min, reset timeout 1ms,typ watchdog timeout 1.6sec |
| MAX2653EUB | MaximIC | GSM900 and DSC1900 dual-band, low-noise amplifier. |
| MX636JQ | MaximIC | 100mV. Auxiliary dB output 50dB range. Low power 0.8mA(typ). |
| MAX6378XR45-T | MaximIC | Ultra-low-power voltage detector, 4.5V |
| MAX4174AJEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 3, 1+ (Rf/Dg) noninverting gain 4, -3dB BW 690kHz. |
| MAX630CJA | MaximIC | CMOS micropower step-up switching regulator |
| REF01CZ | MaximIC | +10V precisioon voltage reference. Max TEMPCO 65ppm/degC. Initial error +-100mV |
| MAX321ESA | MaximIC | Precision, dual-supply, SPTS analog switch. |
| MAX6712SEXS-T10 | MaximIC | Microprocessor reset circuit with manual reset input. Reset threshold 2.93V. Output type active-high push-pull reset. |
| MAX4274AEESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 1.25, 1+ (Rf/Dg) noninverting gain 2.25, -3dB BW 450kHz. |
| MAX631AEPA | MaximIC | CMOS fixed +5V output voltage,adjustable output with 2 resistors step-up switching regulator. 5% output accuracy. |
| MAX6316LUK26BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.630V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| MXD1000SA35 | MaximIC | 5-tap silicon delay line |
